Banks Triple Heat Capable Monster-Ram improves throttle response and fuel economy by eliminating airflow restrictions. The patent-pending system prevents severe engine damage by replacing the failure-prone factory grid heater with the Banks High-Flow Intake Plate. The factory heater can't fail if it's not there. Monster-Ram is the only 50-state emissions-compliant RAM intake elbow.
The all new Monster-Ram® intake for the 6.7L Cummins in your Ram lives up to its name. It is an absolute MONSTER. We pulled out all the stops when developing it.
Your Cummins engine struggles to breathe through its tiny, squashed stock inlet which causes boost loss at the
same flow, while the Banks Monster-Ram® has a wide, unrestricted free-flowing path.
The Monster-Ram® offers unparalleled airflow thanks to its custom-engineered fuel line.
All this without the need for tuning while being 50-state compliant.
Since its debut in 2017, tens of thousands of RAM owners throughout the US and Canada have installed a Monster-Ram
to prevent factory grid failure while enjoying quicker throttle response, improved fuel economy, and better
drivability.
But performance means nothing without reliability
That's why Monster-Ram is engineered and tested to
OEM-level standards. Every part in the Monster-Ram kit, including the proprietary fuel line, is covered by the Banks
Limited Lifetime Warranty.
The Monster-Ram® improves airflow from the intercooler. It flows 72.7 lbs/min with Banks’ New Coil Heater and High-Flow Cast Intake Plate compared to stock's 38.6 lbs/min MAF. That is a huge 88.3% improvement over stock you can feel!
The patented design raises boost without increasing back-pressure at the turbine. The result is improved engine response, efficiency, and headroom for daily driving and heavy hauling.
The secret to the Monster-Ram®'s performance is not just airflow, but the quality and weight of the air it flows. Your Cummins engine is limited in the volume of air it can flow through its 6 cylinders even at max RPM.
By increasing the mass of the air delivered to each cylinder, your stock-tuned engine will breathe more efficiently with less stress, and set the stage for power gains when stacked with a tune.
The Monster-Ram® Kit includes a Banks 750-watt coil heater. Want more cold start heat?
Upgrade your Monster-Ram® to 2250 watts with the Triple Heater Upgrade Kit.
Need even more? 750-watt and 1500-watt billet heaters are also available for easy bolt-on supplemental starting heat.
Bolt-on up to an additional 1500W to your Single or Triple Heat Capable Monster-Ram®.
We followed RAM's cold start recommendations. Per the owner’s manual, RAM recommends the use of the block heater when the temperature drops below 0°F/-17°C and mandates the block heater at temperatures below -20°F/-29°C.
Using a controlled climate chamber, our first test utilized block heat and two Banks coil heaters (1500 watts total). The Monster-Ram® enabled our test truck to cold start down to -30°F/-34°C.
Against RAM’s recommendations, we also attempted to cold start with the same two coil heaters and no block heat. We were able to cold start down to -20°F/-29°C. Adding a third coil heater (2,250 watts total), the truck started at -30°F/-34°C.*
All tests were performed with two intake air pre-heat cycles per the owner’s manual. Intake air temperature is just one factor contributing to a successful cold start. Individual results may vary depending on your vehicle’s age and overall condition.
Add the Banks Engine Cover Kit to conceal the factory emissions equipment with an OEM-plus design engineered specifically for Monster-Ram-equipped RAM 6.7L Cummins pickups and chassis cabs
Due to heat, vibration, and time, a stud and nut from the factory heater grid have been documented to come loose and fall into the intake manifold. Thanks to the engine's 5° rake, the broken bolt rolls downhill into cylinder #6, causing catastrophic failure that requires a complete engine rebuild or replacement from bent valves, damaged pistons, and head.
And, while you’re waiting for the BD screw to arc, melt, and fall into the intake manifold, the stock grid heater collects more soot and reduces airflow. Banks Monster-Ram® eliminates the grid heater. There’s nothing to fail or collect soot.
For peak performance, the Monster-Ram® includes a custom-machined high-flow cast intake plate. This plate is machined to the optimum thickness and features an oversized inlet CNC port-matched to the Monster-Ram® for zero restriction and maximum air density.
Our engineers designed an all-new heating solution for the Monster-Ram®.
This new Banks exclusive coil heater sits vertically inside the Monster-Ram® without hindering airflow. This allows the factory grid heater to be replaced with the Banks High-Flow Intake Plate.
This eliminates the risk of engine failure due to parts loosening and falling into the engine while maintaining OEM-like cold weather engine start performance.
Banks fuel lines are engineered to rigorous automotive quality-control standards using premium raw materials.
Each line is laboratory burst-tested to more than three times the maximum pressure produced by the factory high-pressure fuel pump, then fatigue-tested through 10 million pressure cycles simulating operation from idle to wide-open throttle.
“This has got to be one of the best product victories of my whole career.”
U.S. Patent 1,139,867 S
CA Ind. Des. 249273, 251859, 251860, 251862, 251864
Red, Black or Natural Aluminum | Includes Heater, High-Flow Intake Plate, Upgraded Fuel Line.
2019-2024 Ram 2500/3500 6.7L Cummins
Prevents killer grid heater bolt failure. Improves throttle response. Triple heat capable. Patented.
Banks Triple Heat Capable Monster-Ram improves throttle response and fuel economy by eliminating airflow restrictions. The patent-pending system prevents severe engine damage by replacing the failure-prone factory grid heater with the Banks High-Flow Intake Plate. The factory heater can't fail if it's not there. Monster-Ram is the only 50-state emissions-compliant RAM intake elbow.
The all new Monster-Ram® intake for the 6.7L Cummins in your Ram lives up to its name. It is an absolute MONSTER. We pulled out all the stops when developing it.
Your Cummins engine struggles to breathe through its tiny, squashed stock inlet which causes boost loss at the
same flow, while the Banks Monster-Ram® has a wide, unrestricted free-flowing path.
The Monster-Ram® offers unparalleled airflow thanks to its custom-engineered fuel line.
All this without the need for tuning while being 50-state compliant.
Since its debut in 2017, tens of thousands of RAM owners throughout the US and Canada have installed a Monster-Ram
to prevent factory grid failure while enjoying quicker throttle response, improved fuel economy, and better
drivability.
But performance means nothing without reliability
That's why Monster-Ram is engineered and tested to
OEM-level standards. Every part in the Monster-Ram kit, including the proprietary fuel line, is covered by the Banks
Limited Lifetime Warranty.
The Monster-Ram® improves airflow from the intercooler. It flows 72.7 lbs/min with Banks’ New Coil Heater and High-Flow Cast Intake Plate compared to stock's 38.6 lbs/min MAF. That is a huge 88.3% improvement over stock you can feel!
The patented design raises boost without increasing back-pressure at the turbine. The result is improved engine response, efficiency, and headroom for daily driving and heavy hauling.
The secret to the Monster-Ram®'s performance is not just airflow, but the quality and weight of the air it flows. Your Cummins engine is limited in the volume of air it can flow through its 6 cylinders even at max RPM.
By increasing the mass of the air delivered to each cylinder, your stock-tuned engine will breathe more efficiently with less stress, and set the stage for power gains when stacked with a tune.
The Monster-Ram® Kit includes a Banks 750-watt coil heater. Want more cold start heat?
Upgrade your Monster-Ram® to 2250 watts with the Triple Heater Upgrade Kit.
Need even more? 750-watt and 1500-watt billet heaters are also available for easy bolt-on supplemental starting heat.
Bolt-on up to an additional 1500W to your Single or Triple Heat Capable Monster-Ram®.
We followed RAM's cold start recommendations. Per the owner’s manual, RAM recommends the use of the block heater when the temperature drops below 0°F/-17°C and mandates the block heater at temperatures below -20°F/-29°C.
Using a controlled climate chamber, our first test utilized block heat and two Banks coil heaters (1500 watts total). The Monster-Ram® enabled our test truck to cold start down to -30°F/-34°C.
Against RAM’s recommendations, we also attempted to cold start with the same two coil heaters and no block heat. We were able to cold start down to -20°F/-29°C. Adding a third coil heater (2,250 watts total), the truck started at -30°F/-34°C.*
All tests were performed with two intake air pre-heat cycles per the owner’s manual. Intake air temperature is just one factor contributing to a successful cold start. Individual results may vary depending on your vehicle’s age and overall condition.
Add the Banks Engine Cover Kit to conceal the factory emissions equipment with an OEM-plus design engineered specifically for Monster-Ram-equipped RAM 6.7L Cummins pickups and chassis cabs
Due to heat, vibration, and time, a stud and nut from the factory heater grid have been documented to come loose and fall into the intake manifold. Thanks to the engine's 5° rake, the broken bolt rolls downhill into cylinder #6, causing catastrophic failure that requires a complete engine rebuild or replacement from bent valves, damaged pistons, and head.
And, while you’re waiting for the BD screw to arc, melt, and fall into the intake manifold, the stock grid heater collects more soot and reduces airflow. Banks Monster-Ram® eliminates the grid heater. There’s nothing to fail or collect soot.
For peak performance, the Monster-Ram® includes a custom-machined high-flow cast intake plate. This plate is machined to the optimum thickness and features an oversized inlet CNC port-matched to the Monster-Ram® for zero restriction and maximum air density.
Our engineers designed an all-new heating solution for the Monster-Ram®.
This new Banks exclusive coil heater sits vertically inside the Monster-Ram® without hindering airflow. This allows the factory grid heater to be replaced with the Banks High-Flow Intake Plate.
This eliminates the risk of engine failure due to parts loosening and falling into the engine while maintaining OEM-like cold weather engine start performance.
Banks fuel lines are engineered to rigorous automotive quality-control standards using premium raw materials.
Each line is laboratory burst-tested to more than three times the maximum pressure produced by the factory high-pressure fuel pump, then fatigue-tested through 10 million pressure cycles simulating operation from idle to wide-open throttle.
“This has got to be one of the best product victories of my whole career.”
U.S. Patent 1,139,867 S
CA Ind. Des. 249273, 251859, 251860, 251862, 251864
Overall rating: 4.932288 / 5 from 1403 reviews.
Customers report significant improvements in throttle response, fuel efficiency, and overall performance with the Monster-Ram Intake and Killer Grid Heater Upgrade. The installation process is praised for being easy, and the product's quality and fit are highly commended. Banks products are noted for their top-notch performance and ease of use.
Review topics: [instructions, looks, quality, shipping, difference, fit, performance, price, improvement, video, finish, issues, power, customer service, results, install, fitment, feel, packaging, truck, craftsmanship, design, sound, throttle response, exhaust, service, mechanic, kit, experience, replacement].
"My bolt was still tight when I removed the grid heater but the peace of mind that it won’t be able to destroy my engine was reason enough to upgrade to the Banks monster ram. Install was pretty straightforward and can be done by anyone mechanically inclined and attention to details. I swear it added some additional power but I can’t be sure. I soon after added the pedal monster and iDash which really woke up throttle input."
"Install was not majorly difficult and the directions were spot on. Everything is working perfectly. I installed, the intake with grid heater upgrade, boost tubes and the ram air, cold air intake. Thank for making great products!"
"I can feel the difference between the OEM Intake Acceleration and the Monster Ram Intake Acceleration. It is a great investment and upgrade to my 2017 Ram 3500 with only 127,000 miles on her. I also like the way the Monster Ram Intake brightens up the Engine Bay. Of all the failures, how many can be traced back to the owners NOT letting the Diesel Pre Heat cycle complete it's job."
"The Banks product is a bit pricey, but very high quality. Requires a fairly skilled mechanic to install due to complexity and removal re-installation of high pressure fuel lines. Clean look and engine definitely seems to run stronger. And no more heater grid bolt concern."
"Night and day difference. Intake, boost tubes, elbow and exhaust all done. The truck is deleted but this woke it up. The gas mileage average has gone up 5 MPG. The exhaust tip makes the sound deeper and getting rid of the grid heater helps me sleep at night. Great products! Well done."
"Took a little time to install. Instructions were awesome for the installation. Throttle response and acceleration seem to be better. Most of all the upgrade to eliminate the heating grid nut falling off into the cylinder."
"I am a snowbird was south for the winter. Found Dave Auto in Utah and watched his video on the grid heater failure. I made an appointment at your Banks shop in California just before my trip home to Vernon BC, Canada. The improvement in boost from 15 to 30lbs. Made climb hills with 14,000 lb 5 wheel much easier. I also notice exhaust temperature was 100 degrees cooler. Plan to do the transmission pan and differential cover before my trip south this year. Dave"
"My truck just turned 123000 mile and after reading what the consequences of not doing this upgrade I decided to do it. When my mechanic showed me my old grid heater, it was in good shape. But I certainly am glad I made the upgrade. No more worrying about the condition of the grid heater and definitely having the piece of mind knowing that the dreaded engine destroying grid bolt drop won’t take out my engine. Performance increase is incredible too!!! Can’t say enough about Banks Power! Thanks Gale!!"
"Noticeable difference inhale response. The engine feels livelier through out the rev range. I opted for the multiple heater probes and have not had any cold start issues. Not terribly difficult to install. I also feel much better knowing I no longer have the bit of damoclese hanging over my engine waiting to cost me 15k (grid heater bolt, you tube it if you don’t know). Instructions provided were excellent, and you get a cool banks badge to put on your truck 15 out of 10 would recommend."
"Don’t let anyone talk you out of using Banks or convince you that the grid heater isn’t an issue. My neighbor had a ’22 Big Horn with 177K miles and dropped a bolt from the grid heater, which ended up killing his engine. I have a ’22 Laramie with 77K miles, and I’m relieved that I don’t have to worry about the grid heater issue anymore. I’m also happy that the grid heater itself is gone and that there’s more room for airflow, which should help reduce soot buildup. I’m not a mechanic by any means, but the installation was simple. Banks provided step-by-step instructions, and their customer support was there if I had any questions. The intake looks beautiful, too. I went with the red one, and it looks great under the hood. Overall, I’m extremely happy with the upgrade and, most importantly, I have peace of mind knowing I don’t have to worry about the grid heater anymore."
Your cart is currently empty.
To proceed, please confirm if you would like to add another one into your cart.
To proceed, please confirm if you would like to add another one into your cart.
To proceed, please confirm if you would like to add this item into your cart without checking for compatibility. Otherwise, you can search for your vehicle configuration to see if it is compatible with this part.
