A True Monster Of A RAM

The all new Monster-Ram^® intake for the 6.7L Cummins in your Ram lives up to its name. It is an absolute MONSTER. We pulled out all the stops when developing it.

Your Cummins engine struggles to breathe through its tiny, squashed stock inlet which causes boost loss at the same flow, while the Banks Monster-Ram® has a wide, unrestricted free-flowing path.

The Monster-Ram® offers unparalleled airflow thanks to its custom-engineered fuel line.

All this without the need for tuning while being 50-state compliant.

What It Does

The Monster-Ram^® improves airflow from the intercooler. It flows 72.7 lbs/min with Banks’ New Coil Heater and High-Flow Cast Intake Plate compared to stock's 38.6 lbs/min MAF. That is a huge 88.3% improvement over stock you can feel!

The proprietary design raises boost without increasing back-pressure at the turbine. The result is improved engine response, efficiency, and headroom for daily driving and heavy hauling.

It's All About
Mass Air Flow

The secret to the Monster-Ram^®'s performance is not just airflow, but the quality and weight of the air it flows. Your Cummins engine is limited in the volume of air it can flow through its 6 cylinders even at max RPM.

By increasing the mass of the air delivered to each cylinder, your stock-tuned engine will breathe more efficiently with less stress, and set the stage for power gains when stacked with a tune.

Now Triple Heat Capable
Upgrade to 2250 Watts

The Monster-Ram^® Kit includes a Banks 750-watt coil heater. Want more cold start heat?

Upgrade your Monster-Ram^® to 2250 watts with the Triple Heater Upgrade Kit.

Need even more? 750-watt and 1500-watt billet heaters are also available for easy bolt-on supplemental starting heat.

Bolt-on up to an additional 1500W to your Single or Triple Heat Capable Monster-Ram^®.

Cold Start Test Criteria

We followed RAM's cold start recommendations. Per the owner’s manual, RAM recommends the use of the block heater when the temperature drops below 0°F/-17°C and mandates the block heater at temperatures below -20°F/-29°C.

Using a controlled climate chamber, our first test utilized block heat and two Banks coil heaters (1500 watts total). The Monster-Ram^® enabled our test truck to cold start down to -30°F/-34°C.

Against RAM’s recommendations, we also attempted to cold start with the same two coil heaters and no block heat. We were able to cold start down to -20°F/-29°C. Adding a third coil heater (2,250 watts total), the truck started at -30°F/-34°C.*

• 2024 Ram 2500 4x4 Tradesman, dual cab short bed | Mileage 7,8XX
• Vehicle unmodified apart from Monster-Ram^®
• Minimum 12-hour cold soak at specified temperature
• New Interstate AGM batteries with full state of charge
• AMSOIL Signature Series. 5W40 motor oil
• New MOPAR fuel/water separator
• New MOPAR fuel filter
• New MOPAR air filter
• #1 Diesel fuel

New Engine Cover

Add the Banks Engine Cover Kit to conceal the factory emissions equipment with an OEM-plus design engineered specifically for Monster-Ram-equipped RAM 6.7L Cummins pickups and chassis cabs

Prevents Broken Bolt Engine Failure

Cummins Ticking Time Bomb

Due to heat, vibration, and time, a stud and nut from the factory heater grid have been documented to come loose and fall into the intake manifold. Thanks to the engine's 5° rake, the broken bolt rolls downhill into cylinder #6, causing catastrophic failure that requires a complete engine rebuild or replacement from bent valves, damaged pistons, and head.

The Competition Cheeps Out

Don’t be fooled by band-aids claiming to prevent grid heater failure. BD’s Killer Grid Heater kit is a temporary fix that leave RAM owners with a false sense of security and a fastener held in by nothing more than liquid thread locker.

Leaving Stock Heater
Chokes Performance

And, while you’re waiting for the BD screw to arc, melt, and fall into the intake manifold, the stock grid heater collects more soot and reduces airflow. Banks Monster-Ram^® eliminates the grid heater. There’s nothing to fail or collect soot.

For peak performance, the Monster-Ram^® includes a custom-machined high-flow cast intake plate. This plate is machined to the optimum thickness and features an oversized inlet CNC port-matched to the Monster-Ram^® for zero restriction and maximum air density.

Unrivaled Airflow

Our engineers designed an all-new heating solution for the Monster-Ram^®.

This new Banks exclusive coil heater sits vertically inside the Monster-Ram^® without hindering airflow. This allows the factory grid heater to be replaced with the Banks High-Flow Intake Plate.

This eliminates the risk of engine failure due to parts loosening and falling into the engine while maintaining OEM-like cold weather engine start performance.

GALE'S PICK